rev. page date description: incremental encoder 1 of 4 7/2008 20050 sw 112 th ave. tualatin, oregon 97062 p h o n e phone 503.612.2300 f a x fax 503.612.2383 part number: CZT01 electrical specifications current consumption 100ma or less (under no load) supply voltage 10 v dc supply current 1 ma output resolution (ppr) 12 contact resistance 500m max. insulation resistance 50m min. dielectric strength 50 v ac (50 ~ 60 hz, cut-off current 2 ma) is applied between non-connected terminals and between terminals and the metal frame for 60 5 seconds mechanical specifications detent points 12 detent points each (detent angle: 30 3) shaft play in axial direction 0.3 mm max. rotational torque 14 ~ 40 gf cm rotational life 100000 cycles (at 3~30 cycles per minute with 0.5 ma, 5 v dc load) mounting height 7 0.1mm mechanical strength free from mechanical abnormalities after test (testing detailed in figure 1) environmental specifications operating temp -25 to +85 c humidity 85% rh vibration proof 10 ~ 55 hz / 1.5mm 2h each x, y, z figure 1 mount the product to the p.c.b. and apply a static force of 10 gf cm minimum. contact resistance: 5 max., insulation resistance: 10 m min.
rev. page date description: incremental encoder 2 of 4 7/2008 20050 sw 112 th ave. tualatin, oregon 97062 p h o n e phone 503.612.2300 f a x fax 503.612.2383 part number: CZT01 weather proof characteristics item test condition cold proof after testing at -25 2c for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. measurements will be made within 1 hour after that. condensation will be eliminated. hot proof after testing at 85 2c for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. measurements will be made within 1 hour after that. moisture resistance after testing at 40 2c, 90 ~ 95% rh for 96 hours, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. measurements will be made within 1 hour after that. condensation will be eliminated. temperature cycling after 5 cycles of the following conditions, the encoder will be allowed to stand under normal temperature and humidity conditions for 1 hour. measurements will be made within 1 hour after that. condensation will be eliminated. salt mist the encoder will be checked after the following test: 1) temperature: 35 2c 2) salt solution: 5 1% (solids by mass) immersion time: 5 minutes 3) after immersing, salt deposit will be removed by running water. 4) duration: 2 hours evaluation standard after test: contact resistance: 5 max. insulation resistance: 10 m min. the performance requirements specified in electrical specifications will be satisfied. no corrosion will be recognized in the metal sections of the encoder.
rev. page date description: incremental encoder 3 of 4 7/2008 20050 sw 112 th ave. tualatin, oregon 97062 p h o n e phone 503.612.2300 f a x fax 503.612.2383 part number: CZT01 f sliding noise shaft rotational direction signal output a ? terminal $ &? c.w. b ? terminal % &? a ? terminal $ &? c.c.w. b ? terminal % &? output waveform
2.0 0.079 0.039 -0.0 +0.1 (3 plcs) 0.1975.0 1.0 10.8 0.425 2.0 0.079 0.2 (3 plcs) 0.2767.0 0.1614.1 0.1383.5 0.1 11.6 0.457 0.3 2.5 0.098 2.5 0.098 6.1 0.240 0.2055.2 2.0 0.079 0.15 (2 plcs) x.xxx 0.1mm x.xx 0.3mm x.x 0.5mm tolerance (unless otherwise stated): website: www.cui.com a material sleeve terminal body plating pbt nickel nickel brass brass 20050 sw 112th ave. tualatin, or 97062 phone: 503-612-2300 800-275-4899 fax: 503-612-2383 rohs sc ale: encoder copyright 2008 by cui inc. title: mm [inches] zrj CZT01 pc file name: appr ove d by: dra wn by: un its: pa rt no. 4:1 c zt 01 r ev: 1.8x2.1 (2 plcs) etad noitpircsed .ver 8002/8/7 gniward wen a 9.8 0.386 0.80 0.15 (3 plcs) 0.118 0.1 3.00 1.74 0.069 0.03 p.c.b. layout tolerance: 0.1mm
|
